Bb-electronics Celeron M Universal Network Controller with PC/104 Manuel d'utilisateur

UNO-2170 Celeron M Universal Network Controller with PC/104 extension User Manual

1.3 Safety Precautions The following sections tell how to make each connection. In most cases, you will simply need to connect a standard cable. W

1.4 Chassis Dimensions Figure 1.1: Chassis Dimensions 5 Chapter 1

UNO-2170 User Manual 6

2 2 Hardware Functionality This chapter shows how to setup the UNO-2170s hardware functions, including connecting peripherals, setting

Chapter 2 Hardware Functionality 2.1 Introduction The following two figures show the connectors on UNO-2170. The following sections give you detai

2.3 RS-232/422/485 Interface (COM3~COM4) The UNO-2170 offers two RS-232/422/485 serial communication interface ports: COM3 and COM4. Please refer to

2.3.5 RS-232/422/485 Selection COM3 and COM4 support 9-wire RS-232, RS-422 and RS-485 inter faces. The system detects RS-422 or RS-485 signals automa

2.3.6 RS-485 Auto Flow Control Mode and RS-422 Master/Slave Mode Selection You can set the “Auto Flow Control mode of RS-485 or “Master/Slave＂ mode

2.3.7 IRQ and Address Setting The IRQ and I/O address range of COM3 and COM4 are listed below: COM3: 3E8H, IRQ10 (Independent IRQ), IRQ10 (Share IRQ

2.4 LAN: Ethernet Connector The UNO-2170 is equipped with a Realtek RTL8139C Ethernet LAN controller that is fully compliant with IEEE 802.3u 10/10

Copyright This document is copyrighted, © 2004. All rights are reserved. The origi- nal manufacturer reserves the right to make improvements to the pr

2.8 PCMCIA: PC Card Slot The UNO-2170 provides one PC Card slot that supports CardBus (Card- 32) cards and 16-bit (PCMCIA 2.1/JEIDA 4.2) card stand

2.10 Battery Backup SRAM UNO-2170 provides 512 KB of battery backed SRAM. This ensures that you have a safe place to store critical data. You can no

UNO-2170 User Manual 16

3 2 Initial Setup This chapter introduces how to initialize the UNO-2170. Sections include: • Introduction • Inserting a Compac

Chapter 3 Initial Setup 3.1 Inserting a CompactFlash Card The procedure for installing a CompactFlash™ card into the UNO-2170 is detailed below,

You can select if you wish to combine the chassis grounding point with the system grounding by using an onboard jumper selection. (JP7) Open - Separa

UNO-2170 User Manual 20

A System Settings and Pin Assignments

Appendix A System Settings and Pin Assignments A.1 System I/O Address and Interrupt Assignment Table A.1: UNO-2170 System I/O Ports

Table A.1: UNO-2170 System I/O Ports Address Range Device 3D0-3DF Color/graphics monitor adapter 3F0-3F7 Diske

Product Warranty Advantech warrants to you, the original purchaser, that each of its products will be free from defects in materials and workmanship f

A.2 Board Connectors and Jumpers There are several connectors and jumpers on the UNO-2170 board. The following sections tell you how to configure th

Table A.3: UNO-2170 Connectors and Jumpers Label Function CN1 Phoenix power connector CN2 Ethernet port 1 CN5

A.3 RS-232 Standard Serial Port (COM1~COM2) Table A.4: RS-232 standard serial port pin assignments Pin RS-232 Signal Name 1

A.4 RS-232/422/485 Serial Port (COM3~COM4) Table A.5: RS-232/422/485 serial port pin assignments Pin RS-232 RS-4

A.6 Phoenix Power Connector (PWR) Table A.7: Power connector pin assignments Pin 10/100Base-T Signal Name 1 +9~36VDC

A.8 USB Connector (USB1~USB2) Table A.9: USB connector pin assignments Pin Signal Name Cable Color 1

UNO-2170 User Manual 30

B Programming the Watchdog Timer

Appendix B Programming the Watchdog Timer Bellow is a sample of programming code for controlling the Watchdog Timer function. ----------------------

33 Appendix B

UNO-2170 User Manual iv

UNO-2170 User Manual 34

Contents Chapter 1 Overview ...2 1.1 Introduction ...

Figure 3.1:Chassis Grounding Connection ... 18 3.3 Connecting Power ... 19

1 2 Overview This chapter provides an overview of UNO-2170s specifications. Sections include: • Introduction • Hardware specif

Chapter 1 Overview 1.1 Introduction UNO-2170 is an embedded Application Ready Platform (ARP) that can shorten your development time and offers ric

1.2 Hardware Specifications CPU: Up to Celeron-M 1GHz Ultra low-voltage version Memory: 256/512 MB DDR on board (Default: 256 MB DDR). Battery-ba