Bb-electronics EIR-EXTEND-C - Quick Start Guide Manuel d'utilisateur télécharger pdf

EIR-EXTEND-C-0812qsg

Items Included

Hardware Installation

Front Panel & LED Chart

Quick Start Guide

EIR-EXTEND-C

Ethernet Coaxial Extender

Front Panel LED’s (Ethernet and Line Connections)

Port

LEDs

Status

Description

Ethernet

(RJ-45)

Power1

Power2

Power3

Steady

Power on

Off

Power off

Link/ACT

Steady

Valid Ethernet

connection established

Flashing

Transmitting or

receiving Ethernet

data (ACT stands for

ACTIVITY)

Off

No valid Ethernet

connection nor

transmitting/receiving

Ethernet data

FDX

Steady

Ethernet connection in

full duplex mode

(FDX stands for FULL-

DUPLEX)

Flashing

Collision occurred

Off

Ethernet connection in

half-duplex mode

Line

(BNC)

Remote

Steady

Operating in remote

mode

Local

Steady

Operating in local

mode

Error

Steady

Error occurred

Link

Steady

A valid connection

established between

local & remote

1. The extender is DIN rail mountable and can be

located in environments with temperatures ranging

from -40 to 75°C. Relative humidity should be

between 5% to 95%, non-condensing.

2. Mount the extender on standard DIN rail by hooking

the top rear of the extender on to the top edge of the

DIN rail. As the unit is pressed into the DIN rail, the

spring-loaded bottom tab should snap on, securing

the bottom. To remove extender from DIN rail, use a

small flathead screw driver, pull down on the spring

loaded tab on the bottom of the extender while pulling

bottom outward. The extender can also be panel

mounted using the optional panel mount kit

EIRPMKT.

3. Provide DC power to the unit between 12 – 48 volts.

While only one power source is required to power up

the Ethernet Extender, using two sources provides

redundancy for mission critical applications. The

removable terminal block accepts 14 – 24 AWG wire.

Use copper conductors only, 60/75℃, 14-24 AWG

torque value 4.5 lb-in.

4. Be sure polarity matches diagram next to the

terminal block. Terminals labeled Power are

positive while GND is negative. An optional power

port labeled Power1 is available with use of

12VDC AC to DC power adapter (PS12VDC3P).

5. Set the DIP switch located on the top of the Ethernet

Extender to Loc (Local) or Rmt (Remote). Ethernet

Extenders work in pairs and must have one unit set as

Loc, the other as Rmt.

6. Connect the Ethernet cable to the RJ-45 port on the

front of Ethernet Extender.

7. Connect the coaxial cable to the BNC port on the front

of the Ethernet Extender. Opposite end connects with

paired Ethernet Extender located elsewhere. Coax

cable must be terminated with male BNC or F

connectors. BNC to F-Type adaptor required for F

style connector (included).

o Ethernet Coaxial Extender

o This Quick Start Guide

o BNC to F-Type Adaptor

Note: Extender requires 12 – 48 VDC, 6.8 watts, power

supply (not included).

The LED indicators give you instant feedback on status of

the Ethernet Extender. Both port speeds are auto sensed.

The EIR-EXTEND-C provides one Ethernet port over

existing coaxial cable.

1 2

Quick Start Guide 1

Résumé du contenu

Page 1 - Quick Start Guide

EIR-EXTEND-C-0812qsg 1 Items Included 2 Hardwar

Page 2

EIR-EXTEND-C-0812qsg 4 DIP Switch Settings 5Po

Commentaires sur ces manuels

Pas de commentaire

Bb-electronics EIR-EXTEND-C - Quick Start Guide Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Accessoires de communication Bb-electronics EIR-EXTEND-C - Quick Start Guide. B&B Electronics EIR-EXTEND-C - Quick Start Guide User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Accessoires de communication Bb-electronics EIR-EXTEND-C - Quick Start Guide